SEKCE B - TVÁŘENÍ KOVŮ

Datum: 3.6.2015

13:30 - 13:45
B1
AKSENOV Sergey
National Research University Higher School of Economics, Moscow, Russian Federation
Inverse Analysis of Plane Strain and Uniaxial Compression Tests Performed on Gleeble - VYŽÁDANÁ PŘEDNÁŠKA
13:45 - 14:00
B2
KODZHASPIROV Georgy
Peter the Great St.Petersburg Polytechnic University, St.Petersburg, Russian Federation
Thermomechanical Strengthening of Middle Carbon Structural Steel using Cold Deformation
14:00 - 14:15
B3
TURCZYN Stanislaw
AGH University of Science and Technology, Cracow, Poland, EU
Designing of Hot Rolling and Cooling Conditions for Dual Phase and Coplex Phase Steel Strips
14:15 - 14:30
B4
PIETRZYK Maciej
AGH University of Science and Technology, Cracow, Poland, EU
Accounting for Phase Transformations in Modelling Stresses Occurring during Laminar Cooling and Coiling of Steel Strips
14:30 - 14:45
B5
MALEČEK Ladislav
COMTES FHT a.s., Dobřany, Czech Republic, EU
Numerical Simulation and Material-technological Modelling of Closed-die Forging
14:45 - 15:00
B6
KOCICH Radim
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Experimental Analysis of Stress Conditions during Rolling
15:00 - 15:15
B7
VOREL Ivan
University of West Bohemia in Pilsen, Research Centre of Forming Technology, Pilsen, Czech Republic, EU
Material-Technological Modelling of Controlled Cooling of Closed Die Forgings from Finish Forging Temperature
15:15 - 15:30
B8
BZOWSKI Krzysztof
AGH University of Science and Technology, Cracow, Poland, EU
New Trends in Efficient Modelling of Phase Transformations
15:30 - 16:00
COFFEE BREAK
16:00 - 16:15
B9
NAUMOV Anton
Peter the Great St.Petersburg Polytechnic University, St.Petersburg, Russian Federation
Microstructure Analysis of Heat-Resistant Ni-based Alloy after Dynamic Recrystallization
16:15 - 16:30
B10
OGOLTSOV Alexey
AO Severstal Management, Cherepovets, Russian Federation
STAN 2000: Computer Model for Simulation of Steels Hot Rolling
16:30 - 16:45
B11
DYJA Henryk
Czestochowa University of Technology, Czestochowa, Poland, EU
Analysis of Stress and Strain in Asymmetric Roll Gap
16:45 - 17:00
B12
KLIBER Jiří
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Behaviour of Hot and Cold rolled Fe-Mn (TWIP) Steel
17:00 - 17:15
B13
TKOCZ Marek
Silesian University of Technology, Katowice, Poland, EU
The Effect of Compression aided by Shear Stress on Material Void Closure
17:15 - 17:30
B14
FABÍK Richard
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Influence of Partial Pass on the Plastic Properties of Wire for Steel Ropes
17:30 - 17:45
B15
KUNČICKÁ Lenka
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Intensive Plastic Deformation of Pre-sintered Al Powder
17:45 - 18:00
B16
KAWULOK Petr
VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU
Possibility of Grain Refinement of Low Carbon Steel by Cycling of Temperature or Deformation
18:00 - 18:15
B17
OMRANIAN MOHAMMADI Peiman
University of Applied Science and Technology, Center of FZA, Amol, Iran, Islamic Republic of
Investigation of Austempering Temperature on GGG70 Ductile Iron for Crankshaft of Peugeot 405

Datum: 4.6.2015

09:00 - 09:15
B18
CHABIČOVSKÝ Martin
Brno University of Technology, Brno, Czech Republic, EU
Heat Treatment of Tubes
09:15 - 09:30
B19
VOTAVOVÁ Helena
Brno University of Technology, Brno, Czech Republic, EU
Cooling Homogeneity Measurement during Hydraulic Descaling in Spray Overlapping Area
09:30 - 09:45
B20
SASAKI Shunsuke
JFE Steel Corporation, Handa, Aichi, Japan
Influence of Mandrel Rolling Conditions on Load of Mandrel Bar
09:45 - 10:00
B21
RIDZOŇ Martin
ŽP Research and Development Centre, Podbrezova, Slovakia, EU
Microstructural Aspects of Cold Forming of Precision Steel Tubes
10:00 - 10:15
B22
NOGA Roman
Material and Metallurgical Research Ltd., Ostrava, Czech Republic, EU
Measurement of Axial Force on a Cross-rolling Mill
10:15 - 10:30
B23
ANDREYACHSHENKO Violetta
Karaganda State Technical University, Temirtau, Kazakhstan
Simulation of Fullering Technology as a Plastic Deformation Method for High Quality Forgings Production
10:30 - 11:00
COFFEE BREAK
11:00 - 11:15
B24
IBATOV Marat
Karaganda State Technical University, Temirtau, Kazakhstan
Use of Equal-channel Angular Pressing for Receiving Finished Products from Alloys of the Titan Basiss
11:15 - 11:30
B25
GŁODZIK Marcin
AGH University of Science and Technology, Cracow, Poland, EU
Analysis of the Aluminum Formability in the Incremental Sheet Forming Process
11:30 - 11:45
B26
ŘIHÁČEK Jan
Brno University of Technology, Brno, Czech Republic, EU
Optimization of Hydroforming Die Geometry for Manufacturing of Solar Absorbers
11:45 - 12:00
B27
SHANMUGAVEL Balasivanandha Prabu
Anna University, Chennai, India
The Role of Corrugation Die Parameters on the Mechanical Properties of Aluminium Alloy (AA 5083) Processed by Repetitive Corrugation and Straightening

Datum: 5.6.2015

09:00 - 09:15
B28
CONSTANTINESCU Dan
University Politehnica of Bucharest, Bucharest, Romania, EU
Particularities Regarding the Thermal Radiation in the Heating Furnaces for Metal Forming
09:15 - 09:30
B29
NAIZABEKOV Abdrakhman
Rudny Industrial Institute, Rudny, Kazakhstan
Effect of Pre-heat-treatment on the Structure and Properties of Steel before Equal-Channel Angular Pressing
09:30 - 09:45
B30
LEZHNEV Sergey
Karaganda State Technical University, Temirtau, Kazakhstan
Research of Influence Equal Channel Angular Pressing Combined with a Heat Treatment on the Microstructure of the Steel 45
09:45 - 10:00
B31
WEGLOWSKI Marek
Institute of Welding, Gliwice, Poland, EU
Experimental and Analytical Analysis of Friction Stir Processing process
10:00 - 10:15
B32
YAKOVLEV Sergey
Tula State University, Tula, Russian Federation
Technological Parameters of Drawing with Wall Thinning Symmetric Machine Parts of Double-layer Anisotropic Materials
10:15 - 10:30
B33
LARIN Sergey
Tula State University, Tula, Russian Federation
Pneumorming the Elements of Cellular Sheet Constructions of Square Cross Section from an Anisotropic Material
10:30 - 11:00
COFFEE BREAK

Zpět